ADC0808CCN DATASHEET PDF

The ADC ADC data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital con- verter 8-channel multiplexer and. ADCCCN Texas Instruments Analog to Digital Converters – ADC Obsolete, LTB expires Nov 6, datasheet, inventory, & pricing. ADCCCN datasheet, ADCCCN circuit, ADCCCN data sheet: NSC – 8-Bit uP Compatible A/D Converters with 8-Channel Multiplexer.

Author: Meztirr Gutaxe
Country: Cambodia
Language: English (Spanish)
Genre: Education
Published (Last): 19 September 2008
Pages: 482
PDF File Size: 10.26 Mb
ePub File Size: 18.6 Mb
ISBN: 619-7-76067-877-7
Downloads: 47406
Price: Free* [*Free Regsitration Required]
Uploader: Shasida

This is an input pin which is made high to start conversion.

IC ADC0808

Interface SD Card with Arduino. Analog Channel 1 to 5. This pin is should be temporarily made high to select ADC channel.

The input which is to be converted to digital form can be selected by using three address lines. Clock input; to provide external clock. Step size is the datashet in analog input to cause a unit change in the datasheeet of ADC.

Submitted by admin on 13 October The right input analog voltage can be given to pins from IN1 to IN7, but the IC can read the voltage of only one channel at a time. Since the ADC IC can measure up to eight Analog voltage and also does not have an internal clock slightly requires more components to make it work compared to its predecessor ADC Output digital pins which gives the result of the ADC conversion.

  FILM A CRITICAL INTRODUCTION PRAMAGGIORE PDF

ADC is an 8 bit analog to digital converter with eight input analog channels, i. Hence, if you are looking for a ADC module with a decent resolution of 8-bit that could measure up to 8 channels then this IC is for you. Input pin; a low to high pulse brings data to output pins from the internal registers at end of conversion. When the conversion is complete the EOC pins goes low to indicate the end of conversion and data ready to be picked up. Output 2 -1 to 2 Interface GPS with Arduino.

ADC Pinout, How to Use & Datasheet

Digital output bit 4. These three bits have to be set as shown in the table below to access the respective analog channel. These 7 pins are the input pins for Analog voltage sensor. Has to be given clock signals 0V-5V 20Mhz approx. Or even to use as a standalone ADC module. That is for every increase of Connect to ground of the circuit.

In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the IN1 pin and the present Voltage is read using a voltmeter.

  CW LEADBEATER ASTRAL PLANE PDF

Virgin Galactic — Commercial Space Flight. TL — Programmable Reference Voltage. SPI Module of Arduino.

Start conversion; input pin; a low to high pulse is given. This is an output pin which goes high once the conversion is over. These three pins are used to select the channel.

The ADC adv0808ccn some specific control signals for its operations like start conversion and bring data to output pins.

Once the channel is set it should adc0808cdn enabled by making the Address latch enabled ALE pin to go high momentarily. The step size is decided based on set reference value.

Vref is connected to ground normally.

The obtained value is 2. End of conversion; output pin; goes low when the conversion is over.

What is Web Browser. End of Conversion EOC. It is a pin Eight channel 8-bit ADC module. The default step size is This high-density System-in-Package SiP integrates controller, power switches, and support components.

Choosing Motor For Robots. Choosing Battery for Robots. Has to be made datashwet to get output on output pins. Powers the IC typically with 5V.