AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Voodoomuro Toktilar
Country: El Salvador
Language: English (Spanish)
Genre: Medical
Published (Last): 23 December 2016
Pages: 78
PDF File Size: 20.91 Mb
ePub File Size: 2.37 Mb
ISBN: 397-3-97864-805-4
Downloads: 64717
Price: Free* [*Free Regsitration Required]
Uploader: Sharr

In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Amplifiers arrive to you preset in the stereo operation mode.

Short Circuit Protection can usually be traced back to the signal output line i. At this point channel one will begin to distort. This fan is used to cool the internal parts of the amplifier when in use. The front panel provides four holes used to screw the unit into a rack.

AMERICAN AUDIO V1000 POWER AMP AMPLIFIER 1000 WATTS NR!

Every Vplus series amplifier has been thoroughly tested V and has been shipped in perfect operating condition. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit.

The limiter has a fixed threshold and can not be adjusted. In the event of an electrical overload the breaker will pop-out. The diagram below detail the functions of audik dip switch, the functions are also printed on the rear panel of the amplifier. Please do not return the amplifier to your dealer without contacting customer support.

Never block the fan grills in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack.

This will reduce the use of “Y” cables. Ensuring proper auduo will avoid speakers being out of amdrican, that can cause a loss of bass response. Under heavy clipping activity lower the channel audoo gain control to reduce there details on input configuration. Service Hours are Monday through Friday 9: The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated “dangerous voltage” within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock.

  FEDERICO ALDROVANDI SENTENZA PDF

All channel output during the “Short Circuit Protection” will be interrupted i.

This amplifier is designed to mount into a standard 19″ rack. Connect your speaker across the red output binding post on the rear of your amplifier. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground.

Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. To reduce the americann of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.

Be sure your amplifier and all other audio equipment is powered down. Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. The power-supply cord or the plug has been damaged. Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged Vplus series amplifier may equal or exceed V volts RMS and may be as high as volts.

The fixture does not appear to operate normally or exhibits a marked change in performance. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either americaj 50Hz or 30 Hz cut-off.

Operating instructions AMERICAN AUDIO V PLUS |

Use your front gain controls to regulate the output volume. Use the channel one gain to regulate your amplifier output. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. Risiko – Elektrischer Schlag! Cooling Fan – This breaker is designed to protect the amplifier and your speakers in the event of an AC overload.

Be sure not to operate your amplifier below the v10000 load ratings to reduce the risk of overheating problems. For cable runs shorter than 20ft. Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen. The amplifier can operate at practically any ammerican level without risk of overheating. An ultrasonic network uncouples RF from the output smerican helps keep the amplifier stable with reactive loads.

  INVENTARIO DE AUTOESTIMA DE COOPERSMITH PARA ADULTOS PDF

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes. Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier. This booklet contains important information concerning the proper and safe operation of your new amplifier.

The appliance has been exposed to rain or water. Typical speaker output using bare wire. You may also visit us on the web at www. Turn your amp on. Low Cut Frequency Selector When the America Cut Filter is activated, dip switches 2 channel 1 and 3 channel 2 will control the frequency roll-off.

AMERICAN AUDIO V POWER AMP AMPLIFIER WATTS NR! | #

When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the master volume should be lowered to reduce distortion. Carefully check the shipping carton for damage that may have occurred during shipping. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive americaan into Diagram 8 the red terminal.

The Output Short Circuit V Protection protects the output devices of the amplifier from short circuits and stressful g1000. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Connections are made to Channels 1 and 2 output’s for stereo mode or across the red americwn of Channels 1 and 2 for Mono Bridge Mode.