KINGSPAN K18 PDF

Kooltherm K18 Insulated Plasterboard is a super high performance insulated dry- lining plasterboard suitable for mechanical fixing. Buy mm Kingspan Kooltherm K18 Insulated Plasterboard, a premium performance fibre-free rigid thermoset phenolic insulation core bonded to mm. Kingspan Kooltherm K18 Insulated Plasterboard is a premium performance insulation, with a fibre-free rigid thermoset phenolic insulation core with mm .

Author: Vubei JoJojinn
Country: Poland
Language: English (Spanish)
Genre: Business
Published (Last): 8 April 2018
Pages: 93
PDF File Size: 7.63 Mb
ePub File Size: 3.82 Mb
ISBN: 239-3-70232-989-8
Downloads: 89374
Price: Free* [*Free Regsitration Required]
Uploader: Samugrel

Finishing Tapered edged boards allow the employment of standard dry—lining techniques.

Test – BS —7: Presently there are no availability restrictions, apart from manufacturing lead-times and minimum quantity order levels on the 70mm, 80mm, mm and mm boards.

Contact us to find your local M18 Representative. Write an online review and share your thoughts with other shoppers!

Contact our experienced technical services department today. Kingspan Kooltherm K18 Insulated Plasterboard may be used to line ceilings or infill where an exposed rafter is desired. They should be driven straight with the heads embedded just below the surface of the board. Cutting should be carried out either by using a fine toothed saw, or by scoring with a sharp knife, snapping the board over a straight edge and then cutting the facing on the other side. Boards should be stored inside a building.

K1 should be taken to ensure that the cavity in cavity wall constructions is not bridged kungspan the board or fixing medium in such a manner that would allow the passage of water through to the inner leaf. We’re ready to help. Kingspan Insulation New Zealand We’re ready to help. Product Thickness 35, 40, 50, 60, 70, 80, 90 mm Other thicknesses available upon enquiry. Kooltherm K18 combines kingsapn, dry—lining and vapour control in one board. The reverse facing of K18 Insulated kingspzn is a Composite foil facing autohesively bonded to the insulation core during manufacture.

Boards that have been allowed to get wet should not be used. The insulation core is resistant to short—term contact with petrol and with most dilute acids, alkalis and mineral oils. Search Product Enter keyword.

  DONDE VAN A MORIR LOS ELEFANTES JOSE DONOSO PDF

52.5mm Kingspan Kooltherm K18 Insulated Plasterboard – pack of 15

To find out more about the cookies we use, or to change your cookie preferences i. This method is for application to fair finished brick, block and concrete cavity walls where K18 Insulated Wallboard is to be finished with gypsum plaster. If, however, temporary outdoor storage cannot be avoided then the boards should be stacked flat on a level base, clear of the ground, and completely protected from inclement weather through use of a polythene sheet or weatherproof tarpaulin.

Dry Wall Plasterboard View Instructions. Kooltherm K18 Insulated Plasterboard Model Specification You can also download the comprehensive model specification here. Cutting should kinggspan carried out either by using a fine toothed saw, or by scoring with a sharp knife, snapping the board over a straight edge and then cutting the facing on the other side.

The board should be fully restrained using mechanical fixings. These must be long enough to allow a minimum 25 mm penetration of the supporting timber, and be placed not less o18 10 mm from the edges of the board and be spaced at mm intervals along all supporting timbers. Premium performance rigid phenolic insulation — thermal conductivity as low as 0.

Kingspan K18 Insulated Plasterboard – mm | Foam Insulation |

The board should be fully restrained using mechanical fixings. Mechanical Fixing Directly to Masonry Substrates This method is for application to fair finished brick, block and concrete cavity walls where K18 Insulated Wallboard is to be finished with gypsum plaster.

The R-value will be reduced in the event of the accumulation of dust on the upward facing surfaces and in those cavities that are ventilated. We can also source the following sizes for larger orders In total, nine Kingspan Insulation technologies were employed in the build of the new Aviva Stadium, including Kingspan Kooltherm K7 in the ceiling, a premium performance rigid thermoset insulation with thermal conductivities as low as 0.

  EL YO PIEL ANZIEU PDF

Kooltherm K18 Kingspzn Plasterboard. Fixings should not overlap board edges. To find out more about the cookies we use, or to change your cookie preferences i.

mm Kingspan Kooltherm K18 Insulated Plasterboard

Timbers should be treated where appropriate. Care should be taken not to overdrive screws. Click Tick-Box to select one or more items.

Adhesives containing such solvents should not be used in association with this product. Kkngspan should be driven straight with the heads embedded just below the surface of the board.

Installation is similar to that of standard plasterboard. Bree Industrial Estate Castleblayney Co. The front facing of K18 Insulated Plaster Board is a tapered edge gypsum based plasterboard which readily accepts dry—jointing materials, plaster skim or direct decoration.

Care should be taken kingzpan ensure that the cavity in cavity wall constructions is not bridged by the kingsoan or fixing medium in such a manner that would allow the passage of water through to the inner leaf.

Kijgspan click “Accept and close” to accept the use of cookies on our website. Cutting and Taping View Instructions. The insulation core is resistant to short—term contact with petrol and with most dilute acids, alkalis and mineral oils. The Reverse Face The reverse facing of K18 Kinbspan wallboard is a Composite foil facing autohesively bonded to the insulation core during manufacture. Mechanical K1 to Metal Furring Systems K18 Insulated Wallboard can be fixed by the use of proprietary metal framing systems to brick, block or concrete walls.

K18 Insulated Wallboard can be fixed by the use of proprietary metal framing systems to brick, block or concrete walls. Screws should not be sited less than 10 mm from the edges of the board. Boards must always be placed with the long edge running across the joists, rafters or battens and all edges must be supported.